The Beveled Hanging Frame

We love Tom McCallum’s hanging frame design described below. The framed quilt block has a hook which fits over a hanger on the barn. It’s very strong but heavy. This design is challenging to install high on a gable end. It’s a great design for lower locations where you want to minimize the number of holes in the side of the barn.

Tools required:

tape measure
drill
red Robertson drive
skill saw
4 saw horses
1/8” & ¼” drill bits
       
Prepare two  template patterns made from ¼” plywood, 4” wide by 8’0’’ long

fasten one edge of the pattern to the piece of 1” x 2” x 8’0” with dry wall screws. Scribe a line with a pencil down the entire length of the centre of the pattern or 2” in from edge. Drill pilot holes with 1/8” drill bit at 24” centres down the length of the pattern on the scribed line. First hole and last hole should be started at 6” from the ends of the pattern
 second pattern will have a scribe line down the centre of the pattern same as the first. Then measuring from each end of the 8’ pattern drill pilot holes on the scribed line at 6” from each end, then at 24” from each end and at 42” in from each end.

The template was created so that installers are consistent in the screw placements on the finished product. This eases the job at the barn site installation.

Layout and assembling the frame:   materials required 

5 straight 2” x 4” x 8’ pressure treated
1 straight 2” x 8” x 8’ pressure treated
44 aluminum washers with a neoprene gasket attached
44 - 1 3/4” x # 8 green deck screws
8 - 4” x #10 green deck screws

To lay out, cut 2 of the 2”x4” at exactly 8’0” long and the remaining 3 at 7’ 5” long. The 2” x 8” should be cut at 7’5” long and a 45 degree cut the length, approximately down the centre so the 2 pieces left are equal in width. Starting with the 2- 2”x 4” x 8’ lay them parallel on the saw horses 7’ 5” apart. Lay the 3 - 2”x 4” x 7’5” starting at one at the end, between the 8’ers and the remaining 2 at 32” centres from the starting end. One half of the 2”x 8” now with a 45 degree angle will be placed at the other end of the 8’ers with the angle facing up and in, leaving the square edge facing out. This final piece will be the top of the quilt board frame.

To assemble frame, drill 1 - ¼” pilot hole in the 8’ers 1 ½” deep where each of the 7’ 5” pieces butt into the 8’ers. With the #10 deck screws fasten each 7’5” cross pieces to the 8’ers. Now with the frame assembled, measure from corner to corner of the assembled frame to get frame square. Once square, carefully lay the 2 – 4’x 8’ quilt boards onto the frame so as not to move the frame out of square. When all edges are inline and the pattern of the quilt boards line up, take the first of the two patterns and lay it on the surface of the quilt board. Starting on one edge of what will be the vertical sides, making sure that the 1” x 2” is hanging down and tight against the edge and the ends of the pattern do not over hang the top or bottom of the boards, using the 1/8” bit drill pilot holes through the pre drilled holes in the pattern through the quilt board surface into the pressure treated lumber below. Once the first edge is complete do the same for the other side.

Using the second pattern, lay it along the top of the quilt board keeping the edge of the pattern flush along the edge of the quilt board and making sure the ends of the pattern do not over hang the quilt board. Repeat for the bottom edge. Using this same pattern locate the two middle cross pieces at the 32” centres. Lay the pattern on the surface of the quilt board and measure on each side from either top or bottom of the quilt board to the scribe line on the pattern 32”. This will centre the pattern on the lumber under the quilt board. Using the 1/8” bit, drill pilot holes through the holes in the pattern through the quilt board into the pressure treated lumber. Once all pilot holes have been drilled, use the washers and the 1 ¾” green deck screws and fasten quilt board to frame. The remaining piece of 2” x 8” with the 45 degree angle can be fastened to the structure the quilt board is to be hung.

Installation

Make sure it is installed level and the angle is facing up and away so that the angle on the quilt board frame will lock into it when the quilt board is hung. To secure to the structure, remove a few of the 1 ¾’ deck screws and using 4” # 10 deck screws with the washer in place, screw through the existing pre drilled pilot holes through the quilt board, pressure-treated lumber and into the structure it is to be mounted on.

 

Design by Tom McCallum

Share This Page: http://obqt.ca/QTxCu